matrix cracking造句
例句與造句
- Mechanical analysis of reinforced bar being vertical to matrix crack
基體裂紋的垂直強化筋力學分析 - 2 . the mechanical properties and fracture mode of 3d c / sic depend on the matrix cracks " propagation in interphase
( 2 ) 3dc sic復合材料的力學性能和斷裂模式與基體裂紋在界面相區的擴展方式密切相關。 - 4 . the matrix cracks " deflection can occur along the m / i interface , within the interphase and along the i / f interface , which can be predicted by modeling the matrix cracks " defection
( 4 )基體裂紋會在界面相區內的m i界面、界面相內部和i f界面等多個位置發生偏轉。 - Then it was necessary to study the matrix crack and delamination damages in detail , which occurred with the maximum probability and played the most important role on fwc failure . two models about damage analysis were established b y using energy method and shear lag method . the mechanism of damage and the effect to structure performance caused by damage are studied further
在此基礎上，深入地研究了殼體損傷發生概率最大、而危害又相當明顯的典型損傷類型? ?基體開裂和分層損傷，分別采用能量法和剪切滯后方法建立基體開裂和分層損傷的模型，對損傷的機理和損傷對殼體性能的影響進行了深入的研究。 - Against the background of the microstructural evolution of three dimensional braiding c / sic composites , used such analytical methods as lm , sem and tem , it is studied that the matrix cracks propagate in the composites with different interphase thickness under three - point - bend testing , as well as under the creep testing . the main conclusions are as follows : 1
本文以三維編織c sic復合材料微結構演化為背景，采用光學顯微鏡( lm ) 、掃描電鏡( sem )和透射電鏡( tem )等分析手段，研究了不同界面相厚度的復合材料在三點彎曲測試中基體裂紋的擴展規律，以及基體裂紋擴展對蠕變過程的影響。 - It's difficult to find matrix cracking in a sentence. 用matrix cracking造句挺難的
- It was found that the cracks can penetrate the interphase and the fiber rapidly when the interphase is thin , which causes the low flexural strength and fracture toughness , as well as the composites " brittle fracture . while the interphase is thick , multiple toughening mechanisms such as the crack deflection and matrix cracking can be activated , which cause the composites " flexural strength and fracture toughness is high and the composites " non - brittle fracture
當界面相較薄時，基體裂紋能夠迅速穿過界面相和纖維，復合材料具有較低的彎曲強度和斷裂韌性，表現為脆性斷裂模式；當界面相較厚時，復合材料能產生裂紋偏轉、基體開裂等多種增韌方式，具有較高的彎曲強度和斷裂韌性，呈韌性斷裂模式。 - 3 . the two stages of primary creep and steady - state creep of 3d c / sic correspond to the gradual saturation of matrix crack and the opening of these cracks respectively . the transverse crack is the main contributor to the macroscopic creep strain of 3d c / sic , and its opening is controlled by the creep temperature
( 3 ) 3dc sic復合材料的減速蠕變階段和穩態蠕變階段分別對應著基體裂紋趨于飽和和逐漸張開這兩個過程；橫向基體裂紋是3dc sic復合材料宏觀蠕變應變的主要貢獻者，溫度是影響橫向裂紋張開速度的一個重要因素。 - There are three main kinds of matrix cracks within the as - received composites : cracks induced by mismatch of thermal expansion coefficients , cracks between bundles and cracks induced by matrix ' s delamination . they locate within the bundles , between the bundles and on the surface of the bundles respectively
主要結果如下： ( 1 )研究表明，在原始3dc sic復合材料內部主要存在三種裂紋：熱失配裂紋，纖維束間裂紋和基體分層裂紋，它們分別存在于纖維束內部，纖維束之間和纖維束表層。 - By way of comparing the results obtained from netting theory , compound theory , nonlinear fem and experimental test , the conclusion could be drawn that matrix crack damage surely existed in the cylinder part of structure . when the structure was subject to internal pressure up to 6 . 8mpa , which was the maximum loading of hydrostatic test , the deformation of the global structure and stress and strain distributed in any parts of structure were obtained
通過對網格理論、復合理論和非線性有限元方法計算結果與試驗值之間的相互比較，可以看出：非線性有限元計算結果介于網格理論和復合理論之間，且有限元計算結果與復合理論結果更加接近，表明在水檢壓力下殼體筒段確實存在著基體開裂等損傷。